3.6 18.5 5.9 3.95 0.28 4 . 7 5 apem apem 1000 series - microswit ch jo ysticks comp a ct size robust construction single or du al axis versa tile single or du al pole al terna tive knob selection ip65 abo ve p anel bush or screw mount v4 swit ches v3 swit ches cross or dia gonal opera tion l ow profile www .apem.com 4
1000 series - microswit ch jo ysticks product description general description the 1000 series is a versatile range of low cost switch joysticks and is ideal for light to medium duty environments where proportional control is not a necessity . configurable with either single or double pole switching , the 1000 series can also be specified as screw or bush mounted. the joystick construction is determined by the switches employed. there are two possible construction options, based on the use of either v3 or v4 switches. v4 switches may be specified with 6a or 10a operation, yielding a smaller joystick than the construction employed for v3 switches which yields up to 16a operation. swit ches three switch options are specified as standard. all are configured with change - over contacts, allowing the user flexibility of connection. v4 - 6a/240v a c should be specified where the joystick will be switching smaller current levels. these switches are supplied with gold flash terminals to ensure reliable switching at very low current levels.v4 - 10a/240v a c should be specified where the joystick will be switching larger current levels. v3 - 16a/240v a c should be specified where the joystick will be switching even greater current levels. note: the construction of the joystick employing v3 switches is not available with as many configuration options.life and reliability of the switches is heavily determined by the type of application and parameters such as load. the apem sales team will be happy to provide further advice about the expected switch performance under differing loads or dc supplies. mechanical opera tion all 1000 series are supplied with an open square gate. as a standard option the joystick may be supplied with an additionallimiter set, that allows the customer to retro -fit limiters to reduce the travel to single axis(-), cross (+) or diagonal (x) operation. joysticks are supplied as standard without a cable harness, allowing the user flexibility of connection. alternatively the joystick may be factory configured with fitted limiters or cable harnesses, upon customer request. sealing t wo gaiter options are offered as standard to provide an ip65 above -panel seal. when specifying a bush mount joystick please select gaiter option 5. alternatively gaiter option 1 should be selected for 4 point screw mount joysticks. as standard, an adhesive p .v .c sealing gasket is supplied with all bush mount joysticks, to ensure a good seal between the joystick body and the panel. du al pole opera tion the construction of the joystick is designed such that both switches nominally trigger simultaneously . such simultaneous triggering is subject to a +/-3 degree tolerance (between switches) owing to the mechanical tolerances and hysterisis of each switch. mounting the 1000 series is available in two mounting options, four point screw mount or bush mount. the v4 screw mount option is supplied with m2.5 x 20mm screws, whereas the larger construction of v3 screw mount joystick is supplied with m2.5 x 25mm screws . all screws supplied are slotted, pan head machine screws. levers l ever option 5 provides for a low profile above the panel (41mm), this option is very popular for those applications requiring a compact, stubby design. l ever option 1 is an additional 5mm taller . l ever option 6 should be specified for a push button handle, and lever option 7 is designed for v4 di-pole, or v3 constructions. note: the company reserves the right to change specifications without notice. 5 www .apem.com
1000 series - microswit ch jo ysticks product configura tion technical specifica tion all parameters and dimensions shown maybe subject to specification, please refer to apem for details. 2 2 m m b u s h * conical standard bush mount* cylindrical not supplied screw mount none t all conical ( d ) (d) (0) (1) (00) (5) (f) (1) (h) (m) ( v ) 4 p o i n t s c r e w lever series mounting limiter set gaiter handle poles modifier 6a - v4* (1) (2) (3) 16a - v3 10a - v4* single p ole (1) (2) di-pole* l ong* (1) standard v4* (5) f or p ush button v4* (6) f or di-polev4/v3 (7) + limiter f itted slot limiter f itted (34) (39) 1 d 1 5 f 1 00 5 mechanical life : >5 million operations l ever t ravel degrees from centre : +/-12 l ever material : stainless steel body material : mineral f illed nylon-6 handle material : nylon or aluminium gaiter material : neoprene mounting - screw : 4 x m2.5 stainless (slotted) mounting - bush : single p oint 22mm diameter no. of switches : 2, 4, or 8 nominal current : 6a, 10a or 16a maximum v oltage : 250v a c contacts 6a - v4 : gold contacts 10a - v4 : silver contacts 16a - v3 : silver switch contacts : changeover t ermination : solder (v4) - f aston (v3) contact life : l oad dependent t emperature r ange : -20c to +50c st and ard options the 1000 series is available with a range of standard options. t o specify your joystick, simply choose one option from each column. an example is shown below . example configura tions w eight : 40 grams above p anel seal : ip65 * denotes unavailable with v3 construction. p ush button* (c) r ound 6 www .apem.com
1000 series - microswit ch jo ysticks useful dimensions 43.00 24.50 45.50 45.50 53.50 53.50 41.00 23.00 15.00 20.50 41.00 30.50 16.50 4.00 22.00 24.50 20.00 bezel limiters 18.00 2.55 45 41.00 23.00 20.00 15.00 36.00 44.00 36.00 v4 bush mount v4 di-pole limiters and bezel set v3 screw mount v4 screw mount 7 www .apem.com
1000 series - microswit ch jo ysticks useful dimensions the joystick is mounted from beneath the panel using the 4 x m2.5 machine screws, supplied with the joystick.supplied as standard with the joystick is a round bezel which may be fitted (according to customer preference) to finish the front face of the panel. fitting the bezel is optional, and is not necessary if the panel cut - out finishes the panel. the joystick is mounted from beneath the panel. supplied as standard with all bush mount joysticks is an adhesive p .v .c. sealing gasket. this should be fitted between the joystick and the panel, in applications where a good seal is needed. 36.00 . 0 4 5 5 36.00 5 5 4 . 0 ?2.80 x 4 ?2.80 x 4 20.00 ? 20.00 ? mounting cut - out mounting cut - out mounting cut - out 22.00 9.20 20.00 v4 bush mount - p anel cut - out & mounting inst alla tion v4 screw mount - p anel cut - out & mounting inst alla tion v3 screw mount - p anel cut - out & mounting inst alla tion the joystick is mounted from beneath the panel using the 4 x m2.5 machine screws, supplied with the joystick. supplied as standard with the joystick is a round bezel which may be fitted (according to customer preference) to finish the front face of the panel. fitting the bezel is optional, and is not necessary if the panel cut - out finishes the panel. 8 www .apem.com
|
